BRYSTON OWNER’S MANUAL Instructions For Bryston SST Series Amplifiers Models 3B SST and 4B SST 3B SST and 4B SST Series Amplifiers Table of. Audio manuals and audio service pdf instructions. Find the user manual you need for Bryston 4B SST Stereo Amplifier User Manual. Page 1. Page 2. Page 3. User guide • Read online or download PDF • Bryston 4BSST User Manual • Bryston Receivers and Amplifiers.

Author: Mesho Megar
Country: Saint Lucia
Language: English (Spanish)
Genre: Finance
Published (Last): 21 November 2009
Pages: 71
PDF File Size: 2.16 Mb
ePub File Size: 8.62 Mb
ISBN: 642-5-77485-487-5
Downloads: 87131
Price: Free* [*Free Regsitration Required]
Uploader: Kigis

Connect to this post the – terminal on the loudspeaker.

Bryston 4BSST User Manual

The power up or turn-on of the 4B SST may be activated by remote control voltage. Do not over tighten or the binding post may become damaged. The SST amplifier uses a magnetic-trip circuit breaker 1 to protect the amplifier. The most important installation consideration is ventilation. Brysfon the SST amplifier also see rear panel description Speaker wires should be as short as practical. If both channel LED indicators are unlit the amplifier probably manyal only to be powered on.

Also see installation section on ventilation.

Bryston 4B SST C Manuals

The 1v setting is used when the source is single-ended, or from a transformer coupled balanced source. For this reason do not install anything directly above it.

Persistent Thermal shutdown indicates steps need to be taken to increase airflow across the channel or channels heat sink. Balanced systems provide noise rejection from external electrical interference, so cable length can be very long 50m or longer.

Related Posts (10)  LA REPUBBLICA DELLE STRAGI IMPUNITE PDF

BRYSTON C SERIES 4B SST DIMENSIONAL DRAWING Pdf Download.

Heat Dissipation 8 ohms – Bridged W 8 ohms Max. Each channel selects a gain of 29dB 1v or 23dB 2v. When the power supplies have stabilized the channel will come out brysston mute and the LED will change to green normal operation. Should the breaker trip, lower or remove the amplifier input signals.

The SST control circuitry itself draws less than 2 mA from the control current when operating. Balanced input Vs Single ended input: All Brystln amplifiers are convection cooled. This will ensure the amplifier is protected in future transport.

Then power the unit up normally. Bryston can provide an optional fan package if required. Different input configurations result in slightly different noise readings.

See figure 2 below. Tampering by persons other than factory authorized service personnel, or failure to fully comply with Bryston operating instructions, voids the warranty. The 2v setting provides an amplifier gain – 23 dB. Use paired wire of 22 to 18 gage sufficient in length between the source device and the SST amplifier.

Cables should be dressed away from input and power cables. Master circuit – breaker. The RED binding post is connected to the amplifier output.

The voltage is listed on the label found at the upper right of the rear panel. This includes parts, labour and return shipping to the first owner and all subsequent owners. Never lift the safety ground to the ssst nor remove the ground pin from the plug.

In the event of a defect or malfunction, Bryston will remedy the problem by repair or replacement, as we deem necessary, to restore the product to full performance. Installation 4g rack mounting section if applicable Ventilation. Bridged W 8 ohms Max. The power up or turn-on of the 3B SST may be activated by remote control voltage. In the unlikely event you have a problem and must return it for service you must use the proper packing material.

Related Posts (10)  BIBLIOTECA AJUSCO UPN MX PDF

The 1v setting bryyston the most amplifier gain – 29 dB.

When the channel has cooled to a safe operating condition the channel will return to normal operation. Note that copper wire is malleable and may require further tightening after the initial installation. The circuit feeding the 4B SST should be sufficient so as not to cause the circuit breaker to trip 15 amp min. Banana plugs offer a quick disconnect option.

The amplifier will now power-up only when the control voltage is present on. Do not install directly above other heat generating equipment. Check that the voltage rating on the label conforms with your locality. Any amplifier that is constantly operated into clipping indicates a more powerful amplifier is needed for that application.

The single ended or unbalanced input is provided for pre-amps without balanced output. Additional tightening pressure can be achieved using a coin in the slots of the knob. Cables should be kept as short as practical and should never be terminated with connectors that may become confused for AC power connectors.