Maxim Integrated LM75 Series Board Mount Temperature Sensors are available at Mouser Electronics. Mouser offers inventory, pricing, & datasheets for Maxim. 10 Jul Pin-for-pin replacement for industry standard LM75 and offers improved temperature resolution of °C and specification of a single part. The LM75 is a temperature sensor, Delta-Sigma analog-to-digital converter, and digital over-temperature de- tector with I2C® interface. The host can query the.

Author: Daigal Vudora
Country: Uruguay
Language: English (Spanish)
Genre: Business
Published (Last): 20 April 2008
Pages: 360
PDF File Size: 11.99 Mb
ePub File Size: 15.14 Mb
ISBN: 417-2-89159-623-2
Downloads: 27173
Price: Free* [*Free Regsitration Required]
Uploader: Vudocage

Take note of the large copper area underneath the IC. From Banana Pi Wiki. You May Also Like: The temperature register always stores an bit 2’s complement data giving atemperature resolution of 0. This module is designed specifically for the Banana Pi.

Initial release July There are three selectable logic address pins so that eight devices can be connected on the same bus without address conflict. Although thermal pathways are routed through the package leads as well as the plastic package itself, the package leads serve as the principal thermal conduits because lk75 are made of metal, and, therefore, have lower thermal resistance.

This page was last edited on 14 Mayat I’m wondering if it works as flawlessly, and as easily, as it appears. In all honesty, prior to reading this datasheet I had never heard of I3C.

BPI LM75 Temperature Sensor Module

Included in this section is the recommendation—although it may seem like common sense These will be published when they are tested. Solder a chip and some wires to one of km75 boards then seal it in clear heatshrink to make a robust remote temperature sensor that can be placed against the main power battery or ECU.

Related Posts (10)  101 POZYCJI SEKSUALNYCH I SEKRETNE PUNKTY PDF

Do you have any experience using I3C, good or bad? Navigation menu Personal tools Log in.

This is an early step in the development of a base class and class hierarchy for sensors specific to remotely piloted aircraft, and in particular electric powered pm75.

Board Setup and Configuration. If so, please share your experience with us in the comments section. The image below illustrates how the IC itself, actually the internal diode temperature sensor, functions as the temperature sensing device. Library for the LM75 Llm75 Sensor. This sensor uses the I2C bus protocol to communicate allowing the Arduino standard Wire library to communicate with the device.

Sources for Electronic Parts. Related Hardware and Initiatives. The device is also a thermal detector providing an overtemperature detection output.

An easy way to play with these devices is to get some off eBay. Or, perhaps, TI is so extremely proud of this feature that they felt it deserved being acknowledgment twice? In a previous articleI mentioned how some I2C devices make use lm57 different resistor values for assigning unique I2C addresses.

A Replacement to LM75/TMP75 Digital Temperature Sensors: The Texas Instruments TMP – News

This lk75 temperature resolution is particularly useful in applications of measuring precisely the thermal drift or runaway. Do you have any experience with this addressing design approach? And to be frank, I have found that similar documentation goofs are not uncommon in brand new datasheets. Now, what I find to be equally impressive is that only three ADDR lines are needed for creating 32 individual addresses. The original reason for defining this class was to enable the measurement of the temperature of the batteries and motor controllers used in remotely piloted aircraft, for the purpose of real time data logging and air to ground telemetry.

Related Posts (10)  CONTAINER ARCHITECTURE JURE KOTNIK PDF

Texas Instruments home page Datasheet Written by: L75 creates 4-state options on pins A0 and A1 to provide 16 possibilities. Hopefully, TI will clean up these slight oversights in the next datasheet revision.

Resolving the Signal Part 6: ,m75 my read of this datasheet, I spotted a few minor documentation goofs.

BPI LM75 Temperature Sensor Module – Banana Pi Wiki

Temperature register Temp to store the digital temp reading, and set-point registers Tos and Thyst to store programmable over temperature shutdown and hysteresis limits, that can be communicated by a controller via the 2-wire serial I2C-bus interface. As can be seen in the figure below, the secret to this solution is accomplished l,75 using the SCL and SDA lines, in addition to power and ground, when assigning the addresses.

Quote of the day. Pin A2 has 2-state options bringing the total to Have you had an opportunity to use this new digital temperature sensor, from TI, in any l7m5 your designs?

A Replacement to LM75/TMP75 Digital Temperature Sensors: The Texas Instruments TMP1075

In order to take full advantage of what this digital temperature-sensing Lmm75 offers, Texas Instruments has been generous by providing their Detailed Design Procedure in Section 8. The playground is a publicly-editable wiki about Arduino. Views Read View source View history. The LM75A is a temperature-to-digital converter using an on-chip band gap temperature sensor and Sigma-delta A-to-D conversion technique. The kernel should be recompiled. Bryan Lizon, Texas Instruments. Still, they may be a bit embarrassing for some companies.